[sjhossene]

Hi Prof
Thank you, professor, I did your instructions and the system was fixed and updated.

Thanks

[sjhossene]

Hello Prof Periz
Where we can download last version of SARPROZ. I can not update my sarproze. when I want to update, the below err appeared.

An ERROR occurred and was saved in the file lasterror.mat, directory C:\SARPROZE
The LOG FILE can be found here 09_Nov_2021_12_41_36_sarproz.log, directory C:\SARPROZE
Please read carefully the document below before taking any actions:
C:\SARPROZE\Sarproz_errors_management.html Here a brief error message:

Unsuccessful open: Connection refused: connect
-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
… A Connection Could not be opened, moving forward …
It looks like none of the servers is accessible. Try again later

pleas help me
thanks

[sjhossene]

Hi Prof Periz

Thanks for the quick response,, I’m still having trouble downloading meteorological data from darksky.com ( read_w_darksky: failed reading data online!!!).

I installed a new SARPROZ and Java version, but can not download meteorological data from darksky.com.

Thanks in advance.
SJ-Hossene

Attachments:

You must be logged in to view attached files.

[sjhossene]

Hi Prof Periz

I have encountered a problem recently when I want to download data from the site of darksky.com ( read_w_darksky: failed reading data online!!).
Is this a software issue or is it due to stop and not support the site?
Thank you

[sjhossene]

Hello professor
Thank you for your quick response and accurate.

Please let me ask you three questions in this regard

1- How can we calculate time series changes along east -west and vertical velocity for a given point?

2- Is not possible to export e-w velocity and vertical velocity in Multi- Sensor Module or other section of SARPROZ?

3- What are the positive and negative values ​​in the east-west exit maps?

Thank you

[sjhossene]

Hello professor
Thanks for your quick response.

How can I decomposing them?
I downloaded the last version of the software today and did these steps to to estimate the vertical and E-W components.

1- Imported TS objects for AS&DS tracks and loaded them in the multi-sensor module. In this step PASS and Track in upper table are empty!? while PASS option is in PDF tutorial SW.
2- To Offsets Estimation: set 5,5 and 20 for “Max Planar Distance” , “Max H Dist” and “Nr Bins”, respectively.

3- In this Step, The software gives this message
“”Estimated Offsets: Lat 12.6 [m], Lon 74.2 [m], Height -123.3 [m]
get_ms_pairs: WARNING!!! reference acquisition pass is empty!! “”

So how should I do the steps.

Are there any instructions for doing these steps? Or a PDF training file?

VERY THANKS

[sjhossene]

Hello professor
Thanks for your quick response.
That is true.
These values ​​are along LOS. I generated TS objects for AS&DS and then loaded them in the multi-sensor module and combined them to estimate the vertical components.

Figure A shows combination of Ascending-Descending TS objects.

And Figure B shows combination of Ascending -Descending TS
objects.

As you can see in the figures below , the values have ​​inverse and opposite signs?!

Thank you for explaining why they are the opposite!
Thanks a lot

Attachments:

You must be logged in to view attached files.

[sjhossene]

Hi
Thank you for your quick response.
How can I attend courses or can I upgrade one at my university?
Are there no distance learning courses? (Webinar?)

Best

[sjhossene]

Hi dear colleagues
I have a basic question about “parameters range” in “APS Estimation” or”processing parameters“.
In the “Multi-Image InSAR Processing” section, when i selecting “APS Estimation” , on what basis should values ​​be selected in

1- Linear trend (On what basis parameters range should be chosen?)
2-Hieght (On what basis parameters range should be chosen?)
3-Azimouth shift
4-sespnal terend
Why do I get different results by changing values ​​?!

How to choose the right values in the “parameters range” ?

Tip: I have no knowledge of the area and do not know what is/was the amount of deformation (subsidence or uplift) ?

thanks

[sjhossene]

sjhossene wrote:

Hello
I got a problem !!
On site processing
In the «InSAR processing»
In the «Interferogram processing»

It only goes up to 25% and will not change !!

thanks

Attachments:

You must be logged in to view attached files.

[sjhossene]

Hello
I got a problem !!
On site processing
In the «InSAR processing»
In the «Interferogram processing»

It only goes up to 25% and will not change !!

thanks

Attachments:

You must be logged in to view attached files.

[sjhossene]

Hello dear colleagues
What is the latest version of SARPROZ?
I installed compile_2019-07-15.
Is there a newer version of SARPROZ?
Thanks
Hossine

[sjhossene]

Hi Prof and thanks to reply speedly
when i want to update SARPROZ the below error appear :

Connection SetUp

An error occurred and was saved in the file lasterror.mat, directory C:\SARPROZE

If you need assistance, please send the file lasterror.mat to support@sarproz.com

Please include also file 27_Aug_2019_09_14_37_sarproz.log

Here a brief error message:

Unsuccessful open: Connection timed out: connect

Thank you for your help
Best regards

[sjhossene]

Hello dear colleagues
What is the latest version of Matlab compiler that support by SARPROZ software?

[Author]

Posts